Difference between revisions of "TrainCarts/Signs/Launcher/zh-cn"
(Created page with "=== 第二行 ===") |
(Created page with "''launch'' 或 ''launcher''，接下来是启动配置。启动需要设定距离、设定时间或恒定时间。启动方法可以配置为[https://en.wikipedia.org/wiki/Lin...") |
||
| Line 20: | Line 20: | ||
=== 第二行 === | === 第二行 === | ||
| − | + | ''launch'' 或 ''launcher''，接下来是启动配置。启动需要设定距离、设定时间或恒定时间。启动方法可以配置为[https://en.wikipedia.org/wiki/Linear_线性函数]或[https://en.wikipedia.org/wiki/B%C3%A9zier_贝塞尔曲线]。贝塞尔曲线会在启动开始和结束时加速得更慢。 | |
| − | ''launch'' | ||
| − | |||
<div lang="en" dir="ltr" class="mw-content-ltr"> | <div lang="en" dir="ltr" class="mw-content-ltr"> | ||
Revision as of 18:48, 14 September 2024
介绍
启动器类似于车站，可以启动列车并让它们达到一定的速度。可以指定列车减速/加速的距离和启动方向。启动速度为 0 会使列车慢慢完全停止，类似于车站停止列车的方式。请注意，启动完成后速度不会锁定：你仍然可以推动列车或使其完全停止。
语法
第一行
使用 [cart] 或 [train] 没有区别。 远程控制也可以与启动器结合使用。
第二行
launch 或 launcher，接下来是启动配置。启动需要设定距离、设定时间或恒定时间。启动方法可以配置为[1]或[2]。贝塞尔曲线会在启动开始和结束时加速得更慢。
| Syntax | Meaning |
|---|---|
| launch | Automatically computes a suitable distance to launch at, by looking for the first bend in the rails up ahead.
The maximum distance calculated this way is 100 blocks. |
| launch 20.0 | Launches the train to the target speed over 20 blocks (meters) |
| launch 20.0s | Launches the train to the target speed in 20 seconds |
| launch 1m | Launches the train to the target speed in 1 minute |
| launch 500ms | Launches the train to the target speed in 500 milliseconds |
| launch 100t | Launches the train to the target speed in 100 ticks (5 seconds) |
| launch 2.2G | Launches the train to the target speed at a constant acceleration based on a G-force of 2.2 (0.2406m/t2) |
| launch 10km/h/s | Launches the train to the target speed at a constant acceleration. See the TrainCarts/Acceleration page for more information.
Must have a slash somewhere to be considered an acceleration expression. |
| launch 20l launch 20sl launch 10km/h/sl |
By appending a l at the end of the expression, the launch follows a linear curve. |
| launch 20b launch 20sb launch 10km/h/sb |
By appending a b at the end of the expression, the launch follows a bezier curve. |
Third line
The speed to launch at. If left empty, it will launch at the speed specified in the configuration (launchForce). To put the train to a complete halt, use 0.
Absolute speeds use a positive or zero number with no sign; to launch the train to a speed of 1.25 blocks per tick (25 blocks per second, or 90 km/h), use "1.25". Relative speeds require a sign even when positive; to launch the train to a speed 0.5 higher than it was before, write "+0.5"; to decrease the speed by 0.5, write "-0.5".
When only a value is specified, the unit is blocks/tick. For all other supported units, see TrainCarts/Velocity
Fourth line
Optionally you can specify the direction to launch here. The default parameter, if blank, is "continue" – it will launch the train in the same direction from which it came.