TrainCarts/Signs/Property/en

« Go back

Introduction

Property signs can perform the same tasks as you can do through commands, but then automated. They require redstone power to function and ignore cart ownership, so if you only want it to target trains you own, combine it with a switcher sign checking for owners.

Syntax

[train]

property

speedlimit

1.5

Second line: property

Third line: the property name to change

Fourth line: the value to set the property to

Remote Control

Remote Control You can remotely set properties on trains. Say your train is called train01, then you use the following on the sign:

[train train01]

property

maxspeed

0.4

Properties

The following properties can be set using both [cart] and [train]:

Property	Value example	Meaning
addtag	tag1	Add a single tag
settag	taga	Set to a single tag
remtag	a	Remove a single tag
addowner	Maxxue	Add an owner to the train
setowner	Maxxue	Clear all owners and set to this owner
remowner	Maxxue	Remove a single owner from the train
destination	station2	Set the destination
mobenter	false	Set if mobs can enter
playerenter	true	Set if players can enter
playerexit	yes	Set if players can exit
spawnitemdrops spawndrops killdrops	true	Sets whether carts drop items when destroyed. When disabled, also disables contents of chest/hopper minecarts dropping.

The following properties can only be set using [train]:

Property	Value example	Meaning
name setname rename	Intercity#A	Sets a new name on the train. The #-sign is replaced with a number 1 to infinity.
dname setdname displayname setdisplayname	Trainname	Sets the display name used with trigger signs (%triggernameN%)
exitoffset exityaw exitpitch exitrotation	2/0/0 30 0 90	Change player exit offset, yaw, pitch and rotation.
speedlimit maxspeed	0.6	The maximum allowed speed the train can go
pushing<ref name="collision">Old syntax for compatibility. Replaced by typecollision. See Collision modes</ref>	false	Set if the train pushes mobs, players, trains and misc
pushmobs<ref name="collision"/>	true	Set if the train pushes mobs
pushplayers<ref name="collision"/>	no	Set if the train pushes players
pushmisc<ref name="collision"/>	yes	Set if the train pushes misc (items, boats, etc.)
playercollision mobcollision traincollision misccollision	default cancel kill killnodrops push enter link	Set a collision mode for the train against players, mobs, trains or other types of entities.
slowdown	false	Set if the train slows down, either by gravity or by friction
slowfriction	false	Set if the train slows down due to friction
slowgravity	false	Set if the train slows down, or speeds up, due to gravity
gravity	1.0	Changes the acceleration and deceleration due to gravity (multiplier, 1.0 is default)
linking	deny	Set if the train can link with other trains
collision	allow	Set if the train can collide with other entities
keepcloaded loadchunks keeploaded	true	Set if the train keeps nearby chunks loaded
default setdefault	stat1def	Load one of the default train properties found in DefaultTrainProperties.yml into this train
banking	1 0	Change the banking (First number: Strength, Second number: Smoothness)
godmode invincible	true	Makes a train invincible, so that players cannot destroy it by hitting it. Players with the train.break.any permission (default: OP) can break trains anyway.
waitdistance	2.0	Configures a wait distance, which causes a train to keep distance to other trains up ahead. This works similar to the waiter sign.
waitdelay	3.0	When a train is stopped completely by the waitdistance property, waits this number of seconds after the train can move again.
waitacceleration	0.3 20kmh/s 1.2 1.3	When a train has to slow down or speed up while maintaining distance using the waitdistance property, uses this configured acceleration. When two values are specified separated by a space, then the first value is acceleration (speed up) and the second is deceleration (brake). For more information about the supported acceleration syntax, see TrainCarts/Acceleration.
route add route set route remove route clear	destination_name	Adds/removes/clears/sets the destinations of the route set for a train. Destinations are added at the end.
route load loadroute	my_saved_route	Loads a previously saved route by name.

Set name

The name property alters the name of the train. To account for multiple trains being renamed, and because every train needs a unique name, the # value is added as a counter-based replacement. For example, the first train passing over the property sign with name value: Intercity#A would be named Intercity1A and the second Intercity2A, and so on. You can use this in combination with the spawner sign to spawn trains with a fixed naming system. This naming system can then be used for remote control to control all trains of a certain spawner or category.